HomeMy WebLinkAboutARB201300161 Plan - Other (not approved) 2013-10-22L O C A T I O N
SAL E S MA N
DESI G N ER
DA T E
CU S T O MER
X
X
X
X
X
A
B
C
E
D
1 S T D R A F Tname
NOTES FOR CHANGES
L O C A T I O N
SAL E S MA N
DESI G N ER
DA T E
CU S T O MER
X
X
X
X
X
A
B
C
E
D
Ph. 757-545-8802 • Fax. 757-543-9132
1044 Rur itan Blvd Chesapeake, VA 23324
Des ign-Manuf ac t ure-Ins t all-Serv ic e
Ph. 757-545-8802 • Fax. 757-543-9132
1044 Rur itan Blvd Chesapeake, VA 23324
Des ign-Manuf ac t ure-Ins t all-Serv ic e
C O P Y R I G H T 2 0 1 3 T A L L E Y A N C H O R S I G N C O .
This document is the sole property of Talley Anchor Sign Co. All designs,
manufacturing, reproduction, use and sales rights regarding the same are
expressly forbidden. It is submitted under a confidential relationship for a
special purpose, and the recipient by accepting this document assumes
custody and agrees that this document will not be copied or reproduced in
whole or in part, nor its contents revealed in any manner or to any person
except for the purpose for which it was tendered, nor any special features
peculiar to this design be incorporated in other projects.
C O P Y R I G H T 2 0 1 T A L L E Y A N C H O R S I G N C O . 1 S T D R A F TEXCALIBUR MINERAL
257”
18
”
NOTES FOR CHANGES
2013
2013
09/
CSE
RS
EXCALIBUR MINERAL
10/
10/09/
A
A
A
XXXXXX
XXXXXXX
XXXXXXX
NOTES:
1.) XXX
ALUMINUM HATCH FILLS15% GRAY STEEL HATCH FILLS
See sectional
Detail
Center Line
0' - 0"
0' - 0"
0' - 0"
0' - 0"
0' - 0"
1
1-1
1
X-1
1
X-1
1
X-1
FRONT ELEVATION
SIDE VIEW
TOP VIEW
DETAIL
1" = 8”
3/4" = 1"
3/4" = 1"
3/4" = 1"
COMMON NOTES:
3/16” WHITE LEXAN SOLAR GRADE
FOR UV PROTECTION FROM FADING
ALL GRAPHICS WILL BE 3M - TRANS.
VINYL
CHANNEL LETTERS & BOX SIGN
Info-
LED ILLUMINATED
CHANNEL LETTERS
W/ 3/16” THK TRANS
WHITE FACES W/ SURFACE
APPLIED VINYL
TO MATCH PMS 200C
BRONZE TRIM & RETURNS
LOGO CAN HAS SURFACE APPLIED
DIGITAL PRINT
R/W PAINTED TO MATCH BLDG
SIGN IS APPROX. 18’ ABOVE GRADE
EXCALIBUR MINERAL
EXCALIBUR MINERAL
WALL
ELECTRICAL NOTES
Talley Anchor Sign Co. DOES NOT provide primary electrical to sign.
Power to the sign must be done by a licensed electrical contractor or licensed electrician.
1.A minimum of one dedicated 120V 20 A circuit
2. Junction box installed within 6 feet of sign
3.Three wires: Line, Ground, Neutral
Each sign must have:
RACEWAY-MOUNTED CHANNEL LETTERS
L.E.D. ILLUMINATION. DETAIL: N.T.S.
1. Faces: 3/16” translucent acrylic face fastened to
trim using a 2 part glue adhesive and activator
1“ trim fastened to2. Trim caps
returns with #8 x1/2“ Thred cutting screw.
Quality LEDs for optimal impact3. Illumination:
.043” Aluminum, 5” deep painted &4. Returns:
fastened to R/W
.063 Alum. or better fastened to5. Chnl Backs:
returns with 1/8ӯ pop rivets
Self contained - power supplies, 6. Power Supply:
Input 120VAC Electrical feed through (1) greeneld
wall penetration, Output 12VDC wired to LEDs
through J-Box.UL Listed J-Box mounted for connection
to main electrical.
6.5” (high) x 6.5” (deep) .063 Alum. 7. Raceway:
R/W with easy access lid to service power supply.
1-1/2“ bridge supports internally welded across top.
U.L. listed, weatherproof disconnect box and 8. Switch:
switch located on exterior surface of R/W side.
R/W mounted to wall with required anchors9. Application:
fastened through formed angle.
1/4” drain holes drilled at lowest 10. Weep Holes:
point in each channel box.
2 3 4 5
6
7
8
9
10
EXCALIBUR MINERAL
LED ILLUMINATION.
(THE LEVEL OF ILLUMINATION PROVIDED BY THE
LED LIGHTS WILL NOT EXCEED THE ILLUMINATION
PRODUCED BY A SINGLE STROKE OF 30ma NEON).