HomeMy WebLinkAboutZMA200400004 Action Letter
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -1 -ZMA Code of Development Belvedere The County of Albemarle Submitted by: Stonehaus Development-Owners and Developers
Cline Design Associates, PA Planning and Architecture WW Associates – Civil Engineers October 10, 2005 As Revised: September 22, 2009 As Revised: December 18, 2009 As Revised: January
4, 2010 As Revised: February 3, 2010
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -2 -Table of Contents 1. Purpose and Intent 2. Planned Land Uses 3. The Built Form of Belvedere a. Architectural
Standards b. Landscaping Standards 4. Street Classifications 5. Preservation of historic structures, sites, and archaeological sites 6. Lot Layout Regulations Tables : Table 1: Maximum
Residential Densities and Number of Units Table 2 Minimum Residential Densities and Number of Units Table 3 Developed Square Footage Table 4 Green Space Tabulation Table 5 Amenities
Tabulation Table 6 Permitted /Prohibited Uses by Block Table 7 Minimum Planting Requirements Table 8 Road Standards Table 9 Build-to Lines and other Lot Regulations Appendix A: Carriage
House Unit Regulations Exhibits: 1. Area of Rezoning 2. General Development Plans 2A General Development Plan 2B Block 1 & 2 General Development Plan 2C Blocks 3-10 General Development
Plan 3. Illustrative Development Plan 4. Block 1 & 2 Potential Development Scenario 5. Open Space Master Plan 5A. Block 1 & 2 Open Space Plan 5B. Blocks 3-10 Open Space Plan 6. Concept
Grading Plan Blocks 1 and 2 7. Concept Grading Plan Blocks 3-10 8. Urban Streetscape Cross Section 9. Commons Streetscape Perspective 10. Village Green Perspective 11. Streetscape Sections
12. Development Phasing Plan 13. Belvedere Boulevard/Free State Connector Improvements 13A. Belvedere Drive Pinch Point Option 1 drawing. 14. Boundary Survey 15. Traffic Study 16. Visual
Buffer Areas Block 2
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -3 -BELVEDERE CODE OF DEVELOPMENT 1. PURPOSE AND INTENT Pursuant to Section 20.A.5 of the Zoning Ordinance of Albemarle
County, this document constitutes the Code of Development for the Neighborhood Model District (NMD) for Belvedere. The Belvedere property (“the Property”) encompasses the following parcels
totaling 206.682 acres: TMP 61-00-00-154 Area: 15.079 Acres Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map Designation: Urban Density Proposed Zoning: NM District
TMP 61-00-00-157 Area: 10.991 Acres Owner: Dunlora LLC Existing Zoning: R-4 Land Use Map Designation: Urban Density Proposed Zoning: NM District TMP 61-00-00-158 Area: 14.708 Acres Owner:
Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map Designation: Urban Density Proposed Zoning: NM District TMP 61-00-00-160 partial Total Area: 40.618 Acres 34.929 Acres
being re-zoned Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map Designation: Neighborhood Density Proposed Zoning: NM District TMP 61-00-00-161 Area: 3.477 Acres
Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map Designation: Neighborhood Density Proposed Zoning: NM District TM 62-00-00-2A Partial Area: 10.760 Acres (not being
re-zoned) ½ interest in 5.40 Acres (Belvedere Rd. ROW) 4.228 Acres being rezoned Owner: Jacob C. and Charlotte G. Levenson Existing Zoning: R-4 Land Use Map Designation: Neighborhood
Density Proposed Zoning: NM District TMP 62-00-00-2B (partial, please see “Area of Re-Zoning” exhibit for detail) Total Area: 17.248Acres 1.730 acres being re-zoned Owner: Robert Hauser
Homes, Inc Existing Zoning: R-4 Land Use Map Designation: Neighborhood Density Proposed Zoning: NM District TMP 62-00-00-2C Area: 35.9 Acres Owner: Belvedere Station Land Trust Existing
Zoning: R-4 Land Use Map Designation: Neighborhood Density Proposed Zoning: NM District TM 62-00-00-3 Area: 2.980 Acres Owner: Stonehaus Inc. & Henry Nelson Sprouse Existing Zoning:
R-4 4 Land Use Map Designation: Neighborhood Density Proposed Zoning: NM District TMP 62-00-00-5 Area: 3.243 Acres Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map
Designation: Neighborhood Density Proposed Zoning: NM District TMP 62-00-00-6A Area: 0.657 Acres Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map Designation: Neighborhood
Density Proposed Zoning: NM District TMP 62A3-00-00-1 partial Total Area: 106.15 Acres 78.76 acres being re-zoned Owner: Belvedere Station Land Trust Existing Zoning: R-4 Land Use Map
Designation: Neighborhood Density Proposed Zoning: NM District
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -4 -The code of development for the Belvedere Property is intended to accomplish the following: 1. To promote flexibility
and creativity in establishing the General Development Plan, building locations, mix of uses, bulk requirements, and densities within the Property 2. Establish the framework and standards
for each block in the Property as well as the uses, location, building types, and street systems contained therein Towards this end, the following sections of the Code of Development
are organized to address the standards for the key project elements. Code of Development The Code of Development establishes the requirements set forth in Section 20.A.5 of the Ordinance.
The Code of Development is comprised of text, tables, and appendices. The Code text contains the regulatory requirements in descriptive form for development. It also provides certain
unifying standards that the owner recognizes will require interpretation. Tables and the associated appendices represent the detailed regulatory requirements specified in Section 20.A.5
of the Ordinance. The regulations are supplemented by the text of the Code and where indicated, to establish the specific allowable uses, the proposed range and mix of these uses, as
well as provide a description of planned amenities and minimum improvements, typical street cross-sections, the planned streetscape, and the relationship between planned buildings and
adjacent streets. Relationship of the Code of Development to the Neighborhood Model Section 20.A.5 Section 20.A.5 of the Albemarle County Zoning Ordinance provides the framework for
the Neighborhood Model District. It establishes the regulations by which applicants for NMD zoning amendments are to construct the governing Code of Development for individual projects.
The ordinance stipulates that the Code of Development “Shall establish the unifying guidelines, the specific regulations for the district, and the use characteristics of each block;
provide provide for certainty in the location of an appearance of central features, and the permitted uses in the district; and provide a flexible range of a mix of uses and densities.”
General Development Plan It is the intent of the owner for the General Development Plan (exhibits 2A, 2B, and 2C) to be used by the County Staff in regulating the development of the
Property with the goals and objectives of the rezoning according to the requirements of the county’s NMD district requirements. All other exhibits currently submitted, including the
traffic study, are intended to meet the requirements for a General Development Plan as outlined in the Albemarle County zoning ordinance Section 8 (planned districts) and Section 20.A.5
(Neighborhood Model).
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -5 -The Property will be developed in accordance with the General Development Plan. Road alignments, building and
sidewalk locations, landscaping, grading, and utilities depicted on the General Development Plan may be adjusted at the site plan stage as provided in Albemarle County Code 18-8.5.5.3
so long as they meet the minimum requirements established in the Code. Specific lot boundaries and building locations shown on the exhibits are for purposes of illustration only and
should not be construed as final. Lot boundaries shall be subject to the restrictions outlined in Table 9. Exhibits 8-11, included in the Code of Development illustrate how scale, massing,
and pedestrian orientation may be achieved within the Property, but are not intended to describe final building design. As such, they should be interpreted as a general representation
of the type of architecture or built form planned for the Property. Final zoning interpretation of of the project should not use these illustrations as the standard for review of the
project’s architecture. 2. PLANNED LAND USES Mix of Uses The plan establishes the general mix of uses and the probable amount of those uses to be provided within the project’s designated
block areas. Because of its location, the majority of the uses will be residential. However within this use category, there will be wide range of product types and densities. Land uses
and amenities have been arranged to maximize pedestrian opportunities. The Development Plan generally indicates the location of these uses. The land uses to be permitted will be as indicated
on the Development Plan and as described on a block basis in Appendix B -“Permitted/Prohibited” Uses by Block” Regulating Block Layout The block layout as indicated on the Development
Plan is based on distinct geographic as well as land use conditions and serves as the basis for the Code of Development. The development pattern as identified in the Block Plan relates
to transects that transition from a more urban/dense core near Rio Road and the community center/village green area to the more natural edges of the site. The residential unit count
and densities are shown on the following Tables 1 and 2. The residential units shown below may be adjusted by block and unit type; however the total maximum number of units shall not
exceed 775. The lotting pattern as shown on the Development Plan generally indicates this total number of residential units. Included in these computations are accessory units or carriage
house units. Variation # 26 (approved 2.3.10) modifies Tables 1 and 2 showing maximum and minimum residential units by block and residential density.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -6 -BLOCK GROUP AREA (AC) SFD SFA/TH APARTMENTS/MF CARRIAGE HOUSE UNITS TOTAL DENSITY 1 15.08 20 20 1.3 2 26.83
7 18 294 319 11.9 3 12.48 22 11 33 2.6 4 16.68 30 25 26 81 4.9 5 6.86 31 24 55 8.0 6 9.32 30 9 27 66 7.1 7 8.72 30 32 62 7.1 8 7.9 27 9 26 62 7.8 9 9.41 25 25 2.7 10 93.4 52 52 0.6 TOTAL
206.68 254 61 314 146 775 3.7 BELVEDERE MAXIMUM RESIDENTIAL DENSITIES TABLE 1 MAXIMUM RESIDENTIAL DENSITIES BLOCK GROUP AREA (AC) SFD SFA/TH APARTMENTS/MF CARRIAGE HOUSE UNITS TOTAL
DENSITY 1 15.08 0 0.0 2 26.83 15 218 233 8.7 3 12.48 22 8 30 2.4 4 16.68 28 15 20 63 3.8 5 6.86 29 15 44 6.4 6 9.32 29 20 49 5.3 7 8.72 30 20 50 5.7 8 7.9 24 20 44 5.6 9 9.41 23 23 2.4
10 93.4 50 50 0.5 TOTAL 206.68 235 30 218 103 586 2.8 BELVEDERE MINIMUM RESIDENTIAL DENSITIES TABLE 2 MINIMUM RESIDENTIAL DENSITIES
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -7 -TABLE 3 BELVEDERE DEVELOPED SQUARE FOOTAGE* BLOCK AREA (Acres) COMMERCIAL (Max) COMMERCIAL (Min) RESIDENTIAL
(Approx.)* CENTRAL FEATURES (Min) 1 15.08 60,000 8,000 120,000 2 26.83 30,000 457,200 2,000 (Club) 3 12.48 50,400 4 16.68 20,000 102,400 3,500 (Club) 5 6.86 60,000 6 9.32 79,000 7 8.72
68,000 8 7.9 60,200 9 9.41 70,000 10 93.4 159,000 TOTAL 206.68 110,000 8,000 1,226,200 5,500 At the time of final engineering and architectural plan preparation, it is recognized that
decisions may need to be made that would modify the exact geometry of individual blocks. As such, flexibility in the Code of Development is provided to permit the boundary and acreage
of exact blocks to be increased or decreased at the site plan or subdivision stage by an amount not to exceed 15% of the gross land area of the larger block impacted by each such change.
The following sections describe the general features of each block: Block 1-Due to its proximity to Rio Road, this Block will contain non-residential uses. The buildings will be oriented
toward a central access road and plaza space with diagonal parking and pedestrian oriented streetscape. Illustrative Sections are included in Exhibit 8 to indicate the standards of this
streetscape design. This block will be surrounded on two sides by Open Space areas. Pedestrian and Bike connections will be provided via a greenway corridor along Belvedere Boulevard.
Block 2-With close proximity to Rio Road, potential non-residential uses and the Community Center site, Block 2 has been patterned for higher density residential uses oriented towards
a center median and surrounded by open space on two sides. A neighborhood center serving the recreational needs of the residents in Blocks 1 and 2 will be oriented to the development
in Block to and will back onto Town Run. The greenway corridor along Belvedere Boulevard will extend along the front of Block 2. Variation # 34 (approved 2.3.10) – Change the description
of the above paragraph. “With close proximity to Rio Road, potential non-residential uses and the Community Center site, Block 2 has been patterned for higher density residential uses
oriented towards a center median and surrounded by open space on two sides. A neighborhood center serving the recreational needs of the residents in Blocks 1 and 2 will be oriented to
the development in Block to and will back onto Town Run. The greenway corridor along Belvedere Boulevard will extend along the front of Block 2.”
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -8 -Block 3-This Block includes an entry boulevard into the main residential area of the project with a parallel
greenway corridor and open space along the west side. Houses with alley loaded garages will front the east side of the boulevard and the community center and open space will help to
establish a strong sense of arrival. Block 4-From Roundabout #2 to the terminus of Belvedere Boulevard, Belvedere Boulevard and the Village Green serves as the “main street” of the project.
All housing on this spine would be alley loaded and oriented toward the street. A mix of various lot sizes and multifamily product will be provided throughout the Block. The primary
project Neighborhood Center will be located adjacent to the Village Green. Variation # 15 (approved 9.17.2007) -An indoor fieldhouse will be provided for the purpose of providing a play
amenity to the Belvedere Neighborhood and the Charlottesville/Albemarle Community. Blocks 5 through 8-These Blocks radiate off of the Village Green and Belvedere Boulevard and are characterized
by lots or multifamily residential that are primarily alley loaded. Lots would range between 30’ and 60’ in width with town homes and multifamily interspersed in several locations. Along
the railroad, a 100’ ROW is being reserved for the future Parkway. In the interim, this area will be used for open recreation fields and interconnected to the remainder of the community
with interconnecting trails. Pocket parks and the Neighborhood Center site will serve as the primary amenities and identity of these neighborhoods. SUP 2007-54 (approved 5.14.08) -An
outdoor lit all weather field will be provided for the purpose of providing a play amenity to the Belvedere Neighborhood and the Charlottesville/Albemarle Community. Block 9-As a transition
to the adjacent Dunlora community and steeper, natural areas, this area consists of larger width, front loaded (60’ +) lots and stream buffer conservation areas. Open Space and a 25’-30’
preservation easement along Block 9’s Eastern Boundary will serve to protect mature hardwood vegetation between these lots and the existing Dunlora community. Block 10-This Block encompasses
the outermost transect which is a ridge top overlooking the Rivanna river. The outer edge of this ridge will have front loaded single family homes sited on predominantly larger lots
(60’width and above). Most clearing, grading and home footprints would occur above the 25 % slopes, and Open Space and Linear Park J in the form of conservation and preservation areas
will allow for the retention of large stands of forested area below the clustered lot pattern of Block 10. The focal point of this neighborhood is an oval that contains a small cluster
of alley loaded, ridge top lots (40 width or larger) oriented toward the centralized Park “L”. SUP 2007-58 (approved 5.14.8) -Within the floodplain of the Belvedere Neighborhood, turf
fields will be provided for the active use of the Belvedere Neighborhood and the Charlottesville/Albemarle Community.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -9 -Variation # 19 (approved 9.21.07) -In addition, an Organic Farm will be provided as an amenity to the Neighborhood.
Green Space and Amenities The Property’s open space and amenity system prioritizes the preservation of environmentally sensitive and significant ecosystems such as steep slopes, streams,
and stream buffers, mature deciduous forests, and floodplain. The preservation of these areas has been focused toward significant corridor systems that allow for areas of wildlife and
habitat, water quality buffer, and pedestrian connectivity with greenway amenities throughout the region. The Property open space system is shown in relation to the surrounding open
space on The Open Space Master Plan to illustrate these regional connections. A significant portion of the Property (59.78 acres) has been set aside as Conservation/Preservation Areas
to protect these natural features. Low impact, pervious surface trails will be provided in some of these corridors to allow for pedestrian interconnections and access to the proposed
Rivanna River Greenway. In addition to these areas, 12.63 acres of Green Space have been delineated on the plan specifically to serve as key landscaped focal points within the project.
Large areas of green space will be provided in addition to these numbers in the form of landscapes of road row, road medians, green space within the club, building setback areas, etc.
These additional areas have not been included in the tabulations. A number of buffer areas have been designated in order to diminish the impact of Belvedere on neighboring properties.
All areas identified as buffers within the Code of Development shall be subject to the standards outlined in Albemarle County Code Section 32.7.9.8 in effect on October 5, 2005. The
other components of the open space system are more active and include neighborhood pocket parks, greenways, a central village green, Neighborhood Center site, as well as an anticipated
connection to the Fairview Swim and Tennis Club. The following outlines the general features of each of these amenities: The following is a description of the main green space, parks,
and amenities being provided for both the Property and adjacent communities. Hard Surface Greenway: This trail will provide a multi-use paved connection between Rio Road and the Property
community. The Greenway will be maintained by the Homeowners’ Association and will be a minimum of 8’ in width to accommodate a combination of bike and pedestrian traffic. Signage along
the Hard Surface Greenway will direct members of the public from Rio Road to the Rivanna River Greenway. Park ‘A’ 2.3 acres– Features an existing pond, cemetery site, wooded ravine,
and buffer area between Block 1 and Dunlora to the east. Some grading and utility work may be required in small areas of Park ‘A’ however; the intent is that this will remain a wooded
open space and Conservation Area with supplemental planting as part of the Belvedere Boulevard corridor development. Park ‘A’ will also be used to provide a woodland section of the greenway
trail that parallels Belvedere Boulevard.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -10 -Block 1 green space 0.4 acres-A small area of green space is located between Belvedere Blvd alignment and
the existing Covenant Church site. This area will be retained as landscaped buffer. This landscaped buffer will be subject to the County regulations outlined in Zoning Ordinance Section
32.7.9.8 in effect on October 5, 2005. Block 2 Open Space 6.2 acres-Includes Town Run and adjacent slopes. The Block 2 Neighborhood Center will be oriented toward Park ‘B. Also a storm
water management facility (wet pond) will be located within the Open Space. Major portions of this wooded area will be preserved, however some disturbance will be required for the pond,
some utilities and minor grading. A Class B trail will provide a pedestrian connection between Blocks 1 and 2. A boardwalk with a minimum width of 5’ equipped with handrails shall provide
a means of crossing Town Run. The boardwalk shall be designed in accordance with the standards outlined in Section 4-27 of the Virginia Greenways and Trails Toolbox. An Area located
to the East of the Multi-family buildings will serve as a wooded buffer between Block 2 and the adjacent Rivercrest Community and will be a Preservation Area. The existing stand of trees
will provide a wooded barrier between Block 2 and the existing Rivercrest community. If any tree with a diameter of 12 inch or greater dies of any natural cause within the first 3 years
following final site plan approval for Block 2 the Owner will replace the lost tree(s) with new, 2.5 inch or greater caliper tree(s) of the same species, as measured 24 inches above
ground. Within Areas A and B, as identified on Exhibit 16, the Owner will provide and install a planting of multiple native evergreen species. The planting shall include no fewer than
56 trees and shall be comprised of six (6) foot tall evergreen trees (50%), and eight (8) foot tall evergreen trees (50%). The trees will be located so as to provide the maximum buffer
value to the the Rivercrest Neighborhood. Dispersal of species and sizes shall be random in appearance. The location of new plantings shall be outside the dripline of trees contained
in the Preservation Areas. Block 2 Green Space 0.7 acres-Includes the central green and a green space adjacent to Belvedere Boulevard. Block 2 Neighborhood Center: This facility will
serve the recreational needs of residents of Block 2. This Neighborhood center will feature a clubhouse facility of at least 2,000 ft2. The clubhouse will feature a swimming pool (2,000
ft2 min.), restrooms, changing rooms, and meeting facilities. Block 3 Open Space & SWM #3 4.22 acres: Serves as a buffer between Block 3 and the adjacent neighborhoods, and contains
an existing cemetery and the Free State Road corridor. A low impact trail (‘Class B Standard’)tracing the alignment of a historic road associated with the Free State Community will provide
a connection between these facilities, the existing Rivercrest community, and the Belvedere Blvd. greenway. A portion of the parcel has been reserved for the home of Henry Nelson Sprouse
and his wife and while included in the area of rezoning, is not included in the open space calculation for this area. Lifetime residents of the Free State Community, Mr. Sprouse’s family
has resided in the area for 3 generations. It will also serve as a location for an enhanced extended storm water retention site. Some grading
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -11 -will be required for Alley ‘e’ and adjacent lot development as well as the construction of the BMP however,
the remainder of the site will remain undisturbed. Village Green 1.4 acres-Will serve as a community gathering space and will include a central multipurpose lawn that can be used for
active recreation as well as large gatherings and functions. On the edges will be small, landscaped plazas. Each plaza will include at a minimum, the following amenities: • 4 permanent
benches in each plaza • Each plaza shall be connected to the overall network of sidewalks in the community Block 4 Neighborhood Center-This centrally located facility will be a primary
recreational amenity for the project. It will be interconnected to the other portions of the open space system and residential community through an extensive system of sidewalks and
trails. The main feature of this site will be a Neighborhood Center Building (3,500 ft2. min.) that will be oriented toward the Village Green and adjacent active recreation facilities.
The building will contain meeting rooms, offices, small-scale retail/food and beverage facilities and restrooms/changing rooms. A swimming pool (2,000 ft2 min.) will be adjacent to this
building. Other facilities include tennis and other recreation courts, playground and seating plazas. The Director of Community Development may approve alterations to final program elements
inside the Neighborhood Center and adjacent recreational amenities if he finds that the alterations better respond to neighborhood interests at the time of construction. Variations #16,
17, 18 (approved 9.17.09) -The Neighborhood Center area will provide amenities for the Belvedere development as well as for the Charlottesville/Albemarle community. A field house will
b provided with a footprint of approximately 39,000 square feet which will consist of an indoor multi-purpose playing surface primarily used for soccer as well as associated offices,
locker rooms, storage, and other customary accessory uses. A private educational facility or day care with a building of no more than 8,000 square feet plus outdoor play area will be
provided on the Neighborhood Center site. A community meeting house for Belvedere will be provided in the Neighborhood Center area. This meeting house may include meeting rooms, offices,
small-scale retail/food and beverage facilities, and restrooms/changing rooms. It may also include a hardscape plaza for gatherings. Other amenities for the Belvedere development will
include provision of a minimum of 100 memberships in the Fairview Swim Club. Part of the parking requirements may be satisfied using on-street parking, if determined by the County as
appropriate, as part of the site review process. Block 4 green space-Includes the spaces within the roundabout, edges and focal point areas reserved for intensive landscape amenity treatment.
Park ‘E’ 0.6 acres-This pocket park will include a fenced off leash area for dogs within an area of existing trees and supplemental landscaping. Site amenities such as 3 permanent benches
and sidewalk connections will also be provided. Linear Park ‘F’ 1.7 acres-This park includes one multipurpose grass recreational field with minimum dimensions of 100’ by 175’. The informal
field will not be striped. This park will also include the hard surface trail adjacent to Belvedere Boulevard. Also found within the
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -12 -boundaries of Linear Park ‘F’ is SWM facility #5. Linear Park F shall begin at the current entrance to Fairview
Swim Club and extend North and then West tracing the boundary of the Fairview Swim Club. The park’s boundaries shall be defined as the edge of the ROW to the North and East, and the
property line to the West and South. The Park shall then turn North again extending to the boundary with the Neighborhood Center in Block 4. In this area the park’s boundaries shall
be defined by the individual lot lines and the edge of the ROW for Road L to the East and the property line to the West. It should be noted that the boundaries are inclusive of the 100’
ROW reserved for dedication upon demand by the county for the purpose of constructing the North Free State Connector Road Extension. Such reservation shall remain in place through December
31, 2025. Should this road be removed from the Albemarle County Comprehensive Plan, said reservation shall become null and void. At such time as the county should choose to acquire this
ROW or the reservation of the ROW should expire, the boundaries of this park will need to be adjusted to remove this area from the park’s boundaries. While variable in width, Linear
Park F shall at its narrowest point be a minimum of 15 feet in width. A ‘Class B Standard’ trails will span the length of Linear Park F and serve to interconnect the adjacent Community
Center, housing, and the multi-purpose fields. Park ‘G’ 1.9 acres –this neighborhood park will feature a wet pond and surrounding existing vegetation and re-landscaped park space. The
park will also feature a fenced off leash area for dogs, sidewalks and 5 permanent benches. Park H 0.2 acres-This small neighborhood pocket park will provide an informal neighborhood
gathering spot and will feature 1 permanent bench. Linear Park ‘K’ 0.8 acres– This park shall provide a ‘Class B Standard’
trail which will span the length of Linear Park K and serve to interconnect interconnect the adjacent Neighborhood Center in Blocks 4 and 8. While variable in width, Linear Park K shall
at its narrowest point be a minimum of 15 feet in width. The park shall extend from the boundary of the Neighborhood Center in Block 4 northwards to the boundary of the re-zoning. The
western boundary shall be marked by the edge of the 100’ ROW reservation. The eastern boundary shall be marked by the ROW boundaries for alley’s m, q, and o, as well as the lot lines
for the individual lots in Block 8. Linear Park ‘J’ 5.35 Acres-Includes the Conservation area of steep bluffs and existing woodlands on the south side of the Block 10. An existing clearing
from an old roadbed will be used for much of the ‘class B standard trail that will connect the Property to the Rivanna River bottomlands. As indicated in the Concept Grading Plan (Exhibit
7 “Blocks 3-10 Concept Grading Plan”) additional habitat preservation will be possible on much of the adjacent lots. Open Space Block 10-8.1 Acres– Includes both conservation and preservation
areas to protect the steep bluffs and existing woodlands on the north side of Block 10. As indicated in the Concept Grading Plan, (exhibit 7 “Blocks 3-10 Concept Grading Plan”) additional
habitat preservation will be possible on much of the adjacent lots. Open Space Block 9 & SWM #2, 2.45 Acres – Is primarily for the purpose of providing a vegetative buffer for the adjacent
single family development. The buffer is subject to
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -13 -screening regulations in section 32.7.9.8 in the Zoning Ordinance in effect on October 5, 2005. The area located
to the east of Park G provides for storm water management needs in Block 9 but also serves as a trailhead for a Class B Standard trail that extends through Dunlora and connects the Rivanna
Greenbelt south of Dunlora Farm to the section running through Belvedere. Block 9 Preservation/Conservation Easement – This area, 25 to 30 feet wide extends along the back of the lots
in Block 9, from the Open Space to Linear Park “J”, interrupted only by SWM facility #2. A small portion of this easement (.07 acres) is designated for conservation instead of preservation
to allow for the extension of water and/or sewer from Dunlora. Parks ‘L’ and ‘M’ 0.5 and 0.2 acres-These pocket parks will provide focal points for adjacent lots and will have a mix
of existing vegetation and landscape areas. Park ‘L’ will have a hard surface courtyard space suitable for informal seating and gathering. This courtyard will be connected to the community-wide
network of sidewalks. Rivanna River Conservation Area 41.84 acres-The entire 100-year floodplain area along the Rivanna River will be preserved as open space. This area, as illustrated
in Exhibit 2C, shall be dedicated to the Belvedere Homeowners’ Association upon completion of Phase III. A ‘Class B Standard Trail’ will be constructed along the River frontage that
will be part of the planned Rivanna River Greenway system. Several trail connections will be made through adjacent stream corridors that will provide access to this Riverfront amenity
area. SUP 2007-58 (approved 5.14.8) & Variation # 19 (approved 9.21.07) -The Rivanna River Conservation area will remain as open space but contain an amenity package for the Belvedere
Neighborhood and the Charlottesville/Albemarle Community. This amenity package is to include turf fields, a concession area, and an organic farm.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -14 -Variation # 13 (approved 8.30.07) Table 4 Green Space Tabulation Park or Green Space Block Location Conservation
Area (Acres) Preservation Area (Acres) Other Green Space (Acres) Park 'A' 1 2.3* Block 1 1 0.4 Open Space Block 2 1 & 2 1.2* 5.0* Block 2, Commons and Greenway 2 0.7* Block2 Open Space
including SWM #3 3 4.22 SWM #4 3 0.48 Village Green 4 1.4* Roundabout #2 Corner Pocket Parks 4 1.2* Park 'E' 5 0.6* Linear Park 'F' 6 4.12* Park 'G' 7 1.9* Park 'H' 8 0.2* Open Space
Block 9 9 0.73 1.2 0.5* Block 9, Preservation Easement 9 0.07 0.63 Linear Park 'J' 9 & 10 5.35* Open Space Block 10 10 3.51* 4.59* Linear Park 'K" 10 0.8* Park 'L' 10 0.5* Park 'M" 10
0.2* Rivanna River Bottomland 10 41.85* TOTAL 53.81 Acres 7.62 Acres 22.22 Acres 83.65 Acres Total Green Space or 40% of Site *Included as Project Amenities Table 5 Project Amenities
Parks Listed in Above Table 75.92 Acres Block 2, Neighborhood Center 0.7 Acres Block 4, Neighborhood Center 3.2 Acres 79.82 Acres Total Amenity Area or 38.5% of Site
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -15 -Variation # 13 (approved 8.30.07) This table augments and clarifies open space provision for Blocks 3, 4,
6, and 9. ZMA ZMA REQUIRED REQUIRED REQUIRED PROVIDED PROVIDED PROVIDED PROVIDED "+" = EXCESS BLOCK CHART LABELS CONSERVATION GREEN SPACE TOTAL CONSERVATION PRESERVATION GREEN SPACE
TOTAL "-" = DEFICIT 3 BLOCK 3 OPEN SPACE INCLUDING SWM #3 4.22 4.22 3.71 3.71 (Parcels D, F, H, & I) 3 SWM #4 0.48 0.48 1.44 1.44 (Parcel Q) 3 BOWLES CEMETERY 0 0.21 0.21 (Parcel L)
BLOCK 3 Required Total: 4.7 BLOCK 3 Provided Total: 5.36 +0.66 4A VILLAGE GREEN 1.4 1.4 1.54 1.54 (Parcel M) 4A ROUNDABOUT #2 /CORNER POCKET PARKS 1.2 1.2 0.80 0.80 (Parcels E,N,O,P,S
& T) BLOCK 4A Required Total: 2.6 BLOCK 4A Provided Total: 2.34 -0.26 6 LINEAR PARK F 4.12 4.12 3.34 3.34 (Parcel G, J & K) 6 CORNER POCKET PARK 0.2 0.2 0.08 0.08 (Parcel M) BLOCK 6
Required Total: 4.32 BLOCK 6 Provided Total: 3.42 -0.90 9A OPEN SPACE BLOCK 9 0.73 * 0.73 0.43 0.43 (Parcel R) R) BLOCK 9 Required Total: 0.73 BLOCK 9A Provided Total: 0.43 -0.30 NOTES:
Summary of Blocks 3, 4A, 5A, 6 & 9A: -0.80 To be provided in Block 4C: +0.28 To be provided in Block 9B: +0.25 Deficit in Blocks 3, 4A, 5A, 6 & 9A: -0.27 **THE DEFICIT IN BLOCKS 3, 4A,
5A, 6, AND 9A WILL BE MADE UP IN PHASE 2. OPEN (GREEN) SPACE SCHEDULE (BLOCKS 3, 4A, 5A, 6, & 9A) COMPARISON BETWEEN PRELIMINARY SUBDIVISION DESIGN AND ZMA (AREAS IN ACRES) BLOCK 5A
DOES NOT CONTAIN ANY GREEN SPACE. ALL GREEN SPACE FOR BLOCK 5 WILL BE CONSTRUCTED WITH PHASE 2 IN BLOCK 5B. * THE REQUIRED "OTHER GREEN SPACE" FOR BLOCK 9 IS NOT SHOWN HERE BECAUSE ALL
OF THE "OTHER GREEN SPACE" FOR BLOCK 9 WILL BE CONSTRUCTED WITH PHASE 2 OF BELVEDERE.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -16 -Block 1234 5 6 7 8 9 10 Detached single family R R R R R R R R R Duplexes R R R R R R R R Townhouses R R R
R R R R R R Multiple-family dwellings R R R Assisted living R R Rest home, nursing homes, or convalescent homes R R Agriculture R R R Administrative, Professional Offices R R R Antique,
gift, jewelry, notion and craft shops R R R Auction houses R R Barber, beauty shops R R R Boat Landing and Canoe Livery R Church R R R R Clothing, apparel and shoe shops R R R Clubs,
lodges, civic, fraternal, patritiotic (reference 5.1.2) R R R Commercial recreation establishments including but not limited to amusement centers, bowling alleys, pool halls and dance
halls R R community center R R R R R Convenience store R R R Day care, child care, or nursery facility (reference 5.1.06) R R R Department store R R Drive-Through Windows serving or
associated with permitted uses SP SP Drug store, pharmacy R R R Eating establishment (not including fast fast food restaurant) R R R Farmers' market (reference 5.1.36) R R R Financial
institutions R R R Florist R R R Furniture and home appliances (sales and service) R Hardware store R R Health club or spa R R R Hotels, motels and inns R R Indoor athletic facilities
R R R Indoor theaters R R Laundries, dry cleaners R R Libraries, museums R R R Medical center R Musical intrument sales R Newsstands, magazines, pipe and tobacco shops R R R Office and
business machines sales and service R Optical goods sales R Outdoor amphitheater R R Outdoor eating establishment or café R R R Outdoor storage, display and/or sales serving or associated
with a byriigh permitted use, if any portion of the use would be visible from a travelway SP SP Photgraphic goods sales R R R Private Schools R R R R Professional offices, including
medical, dental and optical R R R Public and private utilities and infrastructure R R School of special instruction R Sporting goods sales R Stand alone parking and parking structures
(reference 4.12, 5.1.41) R R R Stormwater Management Facilities shown on an approved final site plan or subdivision plat R R R R R R R R R R Swim, golf, tennis or athletic facility R
R R R R Tailor, Seamstress R R R Tier I personal wireless service facility or Tier I facility: R R Temporary Construction Uses R R R R R R R R R R Veterinary office and hospital R Visual
and audio appliances sales R Wayside stands -vegetables and agricultural produce (reference 5.1.19) R R R Non Residential Uses Res Uses
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -17 -3. THE BUILT FORM OF BELVEDERE PHILOSOPHY Successful neighborhoods and communities are not random, unplanned
events. In the past, relatively simple planning and controls over time have produced places of such charm and warmth that they have a place in this nation’s collective subconscious.
This memory and those places that survive today have in many ways set the standard for what our new neighborhoods and communities should be. The difficulty lies in creating in a few
years what in the past took several decades. ARCHITECTURAL STANDARDS a. ARCHITECTURAL STYLE A broad range of historic and contemporary American architectural styles (listed below) can
be used as “points-of –departure” for designs at the community of Belvedere. These styles are compatible because they share similar proportions, details, massing, materials, and roof
form. The buildings approved for the Community of Belvedere must exhibit compatibility with these elements elements however unique interpretations of the historic style are allowed and
encouraged. This could mean that the design expression becomes simpler without looking cheap, the details may become simpler but not smaller, or the arrangement of elements may vary
slightly from traditional norms. There should not be so much variation as to be no longer compatible with a more traditional interpretation. The Architectural Standards Committee (“ASC”)
will provide early input to the applicants as to the appropriateness of design and enforce the standards of this code and the Declaration. The Architectural Standards for Belvedere will
be approved by the ASC prior to submission to the County to ensure compliance with the Code of Development. The ASC will review all individual submissions prior to review by the county.
ACCEPTED TRADITIONAL ARCHITECTURAL STYLES • COLONIAL REVIVAL • GREEK REVIVAL • SHINGLE • GEORGIAN AND ADAM • BUNGALOW • ARTS AND CRAFTS • CONTEMPORARY o Restricted to lots with frontage
of 50 feet or greater. GENERAL STYLE, FORM, MASSING AND PROPORTION OF STRUCTURES • The main mass of the building shall have all the ground floors on the same level. Split-level designs
are not permitted without ASC approval.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -18 -• A predominately two-story street elevation is encouraged with a minimum of 50% of homes being two story.
• Similar building elevations shall be separated to minimize the awareness of repetitive floor plans and elevations. For single family detached homes an identical house front elevation
may not be repeated more than once in any grouping of 6 or fewer adjacent lots sharing frontage on a common street. An identical plan may not be constructed on lots that face each other
across a roadway other than an Alley • All front facing gables shall have attic windows. • Entry porches or stoops must provide cover by having a cantilevered, bracketed or column supported
roof, a recessed entry door, or a combination of both. • 9’ minimum ceiling heights at the first level are required. • 50% of the detached homes shall have front porches with a minimum
depth of 7 feet and a minimum width of 15 feet. Lots requiring such porches will be determined by the ASC. • Foundations shall be crawl spaces or partial or full basements. Flat or elevated
slabs will be considered if grading can be accommodated with a minimal impact to existing vegetation. MATERIALS, COLOR AND TEXTURE • All exterior paint colors shall be selected from
the Belvedere Paint Schedule. • Walls shall be no more than one color per material used. • Brick color, range and texture shall be based on the brick choices provided in the Belvedere
Materials Schedule • Stone (cultured or natural) color and style shall be based on the stone choices provided in the Belvedere Materials Schedule • Board and Batten accents using cementious
panels need a batten spacing of no greater than 18” using 5/4”x 3” minimum batten strips. • Roof Shingles style and color shall be selected from the Belvedere Materials Schedule. Other
shingle styles and colors will be considered by the ASC. • Accent color brick may be used if approved by the ASC. • Accent wall patterns of vertical board and batten, trimmed panels
and/and/or shingles will be limited to gables, window bays or other secondary elements or surfaces at the side or alley elevations. The materials for these patterns may be wood or cementious
fiber material. • Precast or cast stone elements may be used if approved by the ASC. • Building wall at the streets shall be finished in modular brick, cultured stone, horizontal lap
siding (4” or 6” to show), stucco or shingle siding • Siding may be wood , cementious fiber material, or vinyl. Accent wall patterns of vertical board and batten, trimmed panels and/or
shingles will be limited to gables, window bays or other secondary elements or surfaces at the side or alley elevations. The materials for these patterns may be wood or cementious fiber
material. Other materials may be considered. • No more than 30% of the homes on any street may incorporate vinyl siding. All vinyl siding shall be selected from the Belvedere Materials
Schedule. Each builder within the community shall be allocated a 30% allowance for vinyl sided units. These allotments are non-transferable and may NOT be used on adjacent lots.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -19 - Vinyl will not be allowed on any corner lot. Vinyl will not be allowed on any lot fronting the Village
Green • Exposed foundations shall be brick, painted concrete, brick embossed or parged. • The building walls veneered in brick should be simple in form and massing. Avoid brick extending
over portions of roof. • Foundations shall be exposed a minimum of 24” at the street sides for homes with a 10 foot setback or less. A flush slab on grade condition can occur at the
alley and side yards or on lots with front yard setbacks of 25 feet or more. • Siding shall be at 4”, 6” or 8” to weather. • Brick shall be modular in size with brown sand mortar. •
A water table detail is required at the street elevation. • Brick selections will be approved by the ASC. • Wood and cementious siding will be painted in accordance with an approved
color scheme prepared by the applicant. Refer to the appendix for general standards on color. No adjacent homes may use the same color scheme ROOF PITCH AND FORM • Roof forms should
be simple and based on the Architectural style selected. • Principal roofs will range from 4:12 to 12:12 based on the selected Architectural style • Secondary roofs can be a lower pitch,
with a minimum of a 2:12 slope seems too flat. • Main roof sections shall have the same pitch. • Dormer design shall be consistent with the selected Architectural style. • Fascia, soffit
and frieze make up the roof to wall design with a full pediment or a cornice return at the gable ends. • Gable attic windows of various shapes often enhance the design along with a full
pediment gable • Rake overhangs are between 6” and 12” on all elevations. • Front Roof overhangs should be a minimum of 12” • The design of the soffit and frieze detail should be given
special attention. The Frieze design should be consistent with the architectural style of the building. • The frieze detail at the street shall continue uninterrupted around the building
unless otherwise determined by the ASC. • Main roofs shall be a 25 year or better “Architectural” dimensional asphalt shingle, a natural slate, standing seam metal or a simulated slate
or flat tile wood shingle or shake. • Ridge vents shall be a rigid plastic designed to receive shingles. Additional roof venting required shall be achieved with gable vents or square
through roof vents painted to match roof color and located away from the street view. • Gutters and down spouts where needed shall be typical ogee profile or half round in metal or vinyl.
• Gutters/downspouts should be connected to storm drainage where possible. • Flat roofs shall have a parapet or railing. • Roof penetrations shall be placed away from view from the street
and placed low on the roof. Paint to match the roof color. • Skylights shall be flat panel and placed out of primary view from the street
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -20 -• Solar panels located on a roof shall be placed within 10 deg. of flush with the roof and outside of primary
view of the street. ARCHITECTURAL ORNAMENTATION • Columns shall be round or square and a minimum of 8” in diameter and made of either wood or fiberglass unless otherwise approved by
the ASC • Railings shall be painted or pre-finished metal or wood. Wood railing visible from the street and under cover shall be finish grade primed and painted with a turned top rail
and based rail. • Foundation vents shall be set into the masonry wall and made of plastic or metal. • Home address numbers shall be selected from the styles shown in the Belvedere color
and material palette and located in a prominent and well-designed location. • No wood front steps will be allowed. Brick steps are encouraged to use shaped brick tread brick FAÇADE TREATMENT
• The Belvedere ASC will provide a list of acceptable window manufacturers. • Windows may be a Wood, Vinyl, or Clad Wood product. They may be pre-finished or field painted. • Window
operating styles may be Double or Single Hung or Casement • Double hung operable windows with true or simulated divided panes are preferred. • Windows with between the glass or interior
applied grills are only permitted with ASC approval. • Full light windows will be reviewed by the ASC on a case-by-case basis. • For all Residential Structures: Large fixed windows can
occur only in combination with operable windows. Small fixed accent windows are accepted. • Main doors may be made of Wood or Fiberglass. Fiberglass doors should have a wood-like texture.
• Garage doors may be made of Wood, Fiberglass, or Metal. • For all Residential Structures: Double hung windows shall have the proportions of a vertical rectangle in the range of 3:1
to 1.5:1 height to width. • Windows may be configured in the building wall singularly or in horizontal groups. • In two story building walls, windows should be stacked or otherwise arranged
in in a regular and symmetrical pattern. • Doors should be arranged with windows in the building wall, usually by stacking a window above the door. • Garage doors occur at the alley
side, or to the side street at an end unit. When the garage is facing a street it should be recessed 18” from the face of the building wall. • Entry doors should have sidelights and/or
transoms. • Arched and curved transoms could be considered at the entry door. • The style of the garage door should be consistent with the Architectural character. • Glazing in the garage
door is encouraged.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -21 -• Window trim is critical to the success of the elevation. A minimum of a 5/4” x 4” trim is required. Window
sills shall be required except where authentic architectural interpretation requires something less • The windows and doors in a brick wall condition shall be trimmed with a brick mold
or 5/4”x material at the jamb and head. • Brick, cast stone, or stone lintels are required unless the frieze covers this condition. • Brick, cast stone, or stone sills are required in
stone or brick walls. • Door trim can be flat or ribbed with a base block. • Doorbells are to be mounted centered in jamb trim. • A water table detail is required at the street elevation.
• Corner trim shall be 5/4” x 6”minimum wood grade B or cementious fiber material. • Nails and screws, if exposed, shall be stainless steel or equivalent. • Careful attention should
be paid to the flashing to allow it to blend with the surrounding materials. • Exterior doors shall be hinged. • Shutter size shall be proportional to the window opening, either full
size or one half size. Shutter style can be louvered or solid. • Shutters must be operable or appear to be by using shutter dogs and blocking behind the inside edge to create separation
between the wall and the back of the shutter. • Shutters must be solid material equal in design and dimension to a wood product. • Gable vents may be wood or fiberglass, and in an appropriate
size and style for the Architectural Style. • Entry Stoops and their steps must be of brick construction and tie into the exposed brick foundation. Where foundations are stucco finish,
stoops and steps may be finished to match. • Front porches shall be of wood concrete or brick construction. Concrete infill is permitted. • Side porches may be of wood or brick construction
with wood or brick steps • Screen porches shall have supports that divide screening into vertical rectangles. • In brick porch construction the skirt and steps are an extension of the
foundation wall. A lightly textured concrete surface is acceptable. Colored concrete or paint is recommended for surface treatment. Stone, tile or brick pavers are also encouraged. •
Porch ceilings shall be plasterboard, beaded planks, or beaded plywood. • Chimneys that occur on the exterior wall at the street side must be veneered in brick or stone. Chimneys that
occur in the roof facing the street must be well detailed and will be considered by the ASC on a case-by-case basis. • Exposed concrete block foundation walls are not allowed. Parged
or painted concrete is allowed. Concrete foundation walls on side or rear should have brick embossed pattern if the front foundation wall is brick. COLONIAL REVIVAL-Based on the Houses
of the Colonial Period, this style is predominately a two-story side gable or gambrel rectangular volume. First and second level windows and doors are typically stacked, but there is
more flexibility in the pattern than with the Georgian and Adam style. Windows are often doubled and change patterns between the first and second level. Roof dormers are a common element.
Symmetry is important but not a rule. EXTERIOR FAÇADE
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -22 -Configuration • Colonial Revival houses are simple rectangular side gabled or hipped two story facades. •
Massing can be symmetrical or asymmetrical. • The entrance should be centered on the front facade if all other elements are symmetrical. • Windows are stacked and typically symmetrical
around a central entry door. • Roof dormers and gable dormers are often an added element. • Chimneys are typically located at the ridge and when at the gable, break the pediment and
project from the wall. • The cornice and entry door surround are elaborately detailed. Simpler details of similar size are acceptable. • A water table course and a second floor level
detail band are common with brick veneer. ROOFS Configuration • There are many derivations of the Colonial Revival style; many roof forms may be applied. • A simple gabled main roof
is the most common with a pitch between 7:12 and 12:12. • Hipped roofs are also common and are generally of a lower pitch. • Dormers in this style may vary greatly in size and detail.
• Dormers are common. They should be small gabled, hipped, or bowed. • Dormers may be used across the roof centered above or between windows. ENTRIES AND PORCHES Configuration • Small
entry porches and full width front porches are common. • Supports are substantial and are spaced a distance apart equal to or just less than their height. • Porches have highly detailed
entry surrounds. • Commonly pilasters are topped with entablatures, pediments, or broken pediments. • Sidelights and transoms typically accompany the paneled entry door. • Small entry
porticos typically have lower pitched or flat roofs that may have a railing and act as a deck to the second floor. • The entry door is typically flush; however recessing the door provides
a sheltered area. WINDOWS AND DOORS Configuration • The windows that exemplify these styles are single or paired double-hung with equal spaces between one another. • For all Residential
Structures: windows windows should be proportioned at least 1:2 (width to height). • Placement from the corner of the house should be at least the width of one window. • First and second
floor windows shall be stacked
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -23 -• Accent windows may appear centered on the peak of a pediment over a balcony, portico, or entry. • For all
Residential Structures: large fixed (“picture”) windows are allowed in combination with tall narrow operable windows to either side. • Bay and bow windows are popular accents. • Shutters
are common in this style. • The front door may be off balanced if it is centered below a second story window. MISCELLANEOUS • Cornice trim to be exaggerated by use of a frieze board
to make the transition from the roof to the wall plane, may be decorated with dental or other type of molding. • Other decorative elaborations are dealt with in other sections of the
text. • Wood pilasters may be located at corners vs. Corner board. • Wood trim at window and door heads to be a wider dimension than the sill and jamb trim. • Two piece trim or more
elaborate trim at the head jamb is encouraged at elevations that are prominent from the street. GREEK REVIVAL -This style is characterized by a simple two-story rectangle with a gabled
or hipped low pitch roof with a heavy cornice line. Typically the entries are symmetrically located and have covered porches. The entry doors have sidelights and transoms. Windows are
usually single elements stacked above each other. EXTERIOR FACADES Configuration • The basic form is a two story rectangular box with either a smaller one and two story boxes may be
added at the rear or sides. The garage can be one of these added boxes to the side or rear. • This style is characterized by a simple two-story rectangle with a gabled or hipped low
pitch roof with a heavy cornice line. • The front gable with a cross gable is also common. • Entries are typically symmetrically located and have covered porches. • Chimneys can be located
on the exterior or interior to the house but are not a dominant element. • Corner trim can be enlarged to appear as a pilaster. ROOFS Configuration • Shallow gable or a hipped roof ranging
between a 5:12 and 7:12 pitch. • Dormers in these styles are very common. • Dormer roofs can be gabled, hipped, or bowed. • Dormers can include fixed or double hung windows, and in the
case of a broken pediment the window may be arched. ENTRIES AND PORCHES
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -24 -Configuration • Entrance doors have sidelights on both sides and the full transom or a broken transom above.
• Full width front porches are possible on one-story side gables. • On two story facades, a one story flat or low-pitched roof covers the porch. • Supports are substantial and are spaced
a distance apart equal to or just less than their height. • The entry doors have sidelights and transoms. • Small entry porticos typically have flat roofs that may have a railing and
can act as a deck to the second floor. • The foundations at the entrance porches will be solid masonry walls or solid piers below columns with lattice in-fill of masonry or wood trim.
• Door assembly can be incorporated into an elaborate trim surround. • Use square or round columns at entry porches proportioned with the building. WINDOWS AND DOORS Configuration •
The windows that exemplify these styles are double hung and singularly placed at equal intervals between one another. • They should be proportioned at least 1:2 (width to height). •
Placement from the corner of the house should
be at least the width of one window. • For visual clarity second story windows should be centered on the windows below and should share the same width as the windows below. • Small round
or square windows may appear centered on the peak of a pediment over a balcony, portico, or entry. • A fairly strict pattern of “five windows over four and a door” is followed. • Windows
may appear more irregularly placed on secondary volumes and side elevations. • Shutters are common in this style. GEORGIAN AND ADAM -Popular styles in this part of the country both past
and present. One story versions and gambrel subtype, but the most common example is a two story rectangular mass with a side facing gable. The entries have elaborate crowns and pilasters,
and typically a single row of transom glass. In the Georgian style the transom is flat while the Adams style is characterized by a bow or arch. Windows occur singularly, they are double
hung, and have nine to twelve panes per sash. Decorative moldings typically emphasize the cornice. The Adams style allows a more elaborate entry, which includes a special window design
above the entry door at the second floor. EXTERIOR FACADE Configuration Georgian and Adams houses are simple rectangular side gabled or hipped two story facades. Windows are stacked
and typically symmetrical around a central entry door. Roof dormers are often an added element.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -25 -Chimneys are typically located at the ridge and when at the gable, do not break the pediment. The cornice
and entry door surround are elaborately detailed. Simpler details of similar size are acceptable A water table course and a second floor level detail band are common with brick veneer.
ENTRIES AND PORCHES Configuration Small entry porches are common. Both these styles have highly detailed entry surrounds. Commonly pilasters are topped with entablatures, pediments,
or broken pediments. Sidelights and transoms typically accompany the paneled entry door. Arched or elliptical transoms are a distinctive feature of the Adam style. The entry door is
typically flush, however recessing the door provides a sheltered area. Porticos are common in the Adam style. WINDOWS AND DOORS Configuration The windows that exemplify these styles
are double hung and singularly placed at equal intervals between one another. They should be proportioned at least 1:2 (width to height). Placement from the corner of the house should
be at least the width of one window. First and second floor windows shall be stacked Accent windows may appear centered on the peak of a pediment over a balcony, portico, or entry. The
Adam style differentiates itself by its’ arched entry transom and a unique window above the entry. Shutters are common in this style. Fences and Walls: The Master Plan for Belvedere
works to develop a strong sense of community. Accordingly fencing must be planned and constructed in a manner that enhances this sense of community. General Regulations: • The finished
side of fences must always face out from the lot • Both sides of all fences must be painted or stained • Chain link fencing is not allowed • The preferred material for free-standing
walls is brick with a minimum width of 8” and capped with a minimum overhang of 1” For Brick walls the brick used in freestanding walls shall match the brick used in the primary residence.
• Retaining walls visible visible from the street shall be fronted with brick or stacked field stone. Retaining walls not visible from the street may be constructed of smooth finished
concrete, architectural block or pressure treated wood.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -26 -• Privacy fences are restricted to side and rear yards and may not exceed 8’ in height. Fences are required:
• On a side yard adjoining a neighborhood park or public right of way a fence is required along the lot property line to provide definition of public spaces (lots separated from the
park by a street or alley shall be exempt from this requirement) • To screen trash receptacles and air conditioner compressors from public view one of the following must be constructed
o an approved fence of adequate height, o suitable wall enclosure o landscape screening • Along the Right hand (As viewed from the primary street frontage) of the lot from the rear corner
of the primary residence to a point 5’ from the rear property line a solid privacy fence of at least 6’ must be constructed. Lots with frontage greater than 60’ may be exempted from
this requirement on a case by case basis. Fences are permitted: • In front yards a lot a 3’ picket fence is permitted along the entire length of the lot line. Whenever possible the fence
should tie back into the front corner of the primary residence. Gates or other openings are permitted for the front walk. The post at the end of the fence shall be decorative and not
less 6” x 6” with a decorative cap. Walls of the same height, compatible with the masonry material of the house, or an evergreen hedge are also acceptable for this use. Pools and Fountains:
The ASC will review all proposed pools on an individual basis. Pool and equipment enclosures must relate architecturally to the primary residence and other structures in their placement,
materials and architectural detailing. NO above ground pools or inflatable bubble covers will be permitted. Site Lighting: All proposed site and landscape lighting shall be detailed
on the Site and Landscape Plans. Lighting shall be subtle in nature. No exterior lighting shall be permitted when in the opinion of the ASC, it would create a nuisance to the adjoining
property owners or the community at large. Gutters and downspouts: Gutters and downspouts shall be designed to be compatible with the roof, fascia and architectural design of the house.
b. LANDSCAPE AND STREETSCAPE STANDARDS
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -27 -The general theme and focus of the landscape treatment throughout the project will be to encourage the use
of plant materials that are less reliant on the use of irrigation, fertilizers and pesticides. Street trees will be installed for all streets, boulevards and roundabouts as listed on
the Road Standards (Table 8) subject to utility placement, easements, buildings and sight distance requirements. Plantings for the parkway and shoulder boulevard classifications may
be more informal and arranged in more natural shade and ornamental tree plantings. Streetscape development for non-residential areas will be more urban in nature and the guiding principles
will be indicated in the following section. The purpose of the Landscaping Standards is to: 1. Promote compatible and continuous landscape treatment throughout the Belvedere community.
The intent is to integrate the lots into the larger community and bridge the gap between public and private spaces. 2. Promote the quality image of the community. Successful landscaping
design provides screening, enhances the architecture of the community, and sets a standard for high quality development. 3. Ensure that the plant material proposed is compatible with
the environmental conditions in Albemarle County and is suitable for creating an aesthetically pleasing year-round environment. 4. The Belvedere Architectural Standards Committee shall
be solely responsible for enforcement of all landscaping standards contained herein. The Belvedere Landscape Palette Only plant material from the proposed Belvedere Landscape Palette
may be used in rights-of-ways, front setback zones, open spaces, and back or side yards of lots adjoining public open spaces. Plants of similar characteristics may be added to the list
upon approval by the ASC. The Landscape Pallette shall be developed by the Owner working in conjunction with a landscape architect and the ASC prior to approval of the Final Site plan
for Phase I. The Natural Planting Approach: Plant materials should complement the native vegetation and be compatible with the ecological and climatic conditions in Albemarle County.
Views can be improved without extensive clearing of the native flora. The cutting of the forest understory to open up views is permissible but should be kept to a minimum and must be
done within the constraints of all established conservation buffers noted on the plat. Landscaping efforts should concentrate planting efforts adjacent to the house, especially near
the entry. Ornamental plants, if used correctly, provide a transition from the natural character of the site to more finished areas closer to the house. For maximum appeal, mix textures
and colors but keep the plan simple. A better effect can be achieved from using quantities of a few species rather than a few plants each of many species.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -28 -The planting plan itself shall sufficiently screen utility areas, break up the foundation of the building,
buffer driveway and parking areas adjacent to property lines, and provide cover for areas disturbed during construction. Foundation plantings shall screen foundations or spaces under
decks. Lawns Sod is required in the front yard of all houses and between the curb and the sidewalk, and is to be wrapped around the side yards for a minimum of 10 ft. Sod should meet
the side property lines as closely as possible to ensure a smooth transition from one lot to another. Beds for existing trees can break the sod along the property line. Any beds for
hedges buffers, or shrub masses meeting the property line must be approved by the ASC which will take into account the consideration the landscaping on the adjoining lot. Corner lots
are considered to have two front yards. Sod is required along the side street from the curb to sidewalk and from the sidewalk to the build-to line. The area between the curb and the
back of sidewalks and between the alley pavement and the rear property line are considered part of the owner’s lot for purposes of maintenance of lawn areas. Street Trees: Street trees
with a minimum caliper of 2 ½” 1 foot above the ground are to be planted on both sides of all streets and lanes in the right-of-way, with a spacing no greater than 50 feet on center
throughout the neighborhoods. Generally these trees will be planted by the applicant once street and house construction is completed on a given block. The timing of tree planting will
be coordinated to coincide with the growing season. Tree Planting On Private Residential Lots On any lot with more than 40’ of frontage, there shall be at least one tree, selected from
the Belvedere Landscape Palette, of at least 2 ½” planted in the front yard of each lot. An additional tree of at least 1 ½” will required in the front yard for each 25 feet of lot frontage
(or fraction thereof) after the initial 50 feet of lot frontage. Tree planted to satisfy this requirement should be located to complement the street tree plantings. If a significant
number of quality trees are retained in the front of the lot then this requirement may be reduced or waived. Minimum Planting Requirements: A minimum plant quantity chart is provided
below to assist the owner/builder in developing landscape plans. These quantities are minimums for the front of houses, additional plants beyond these numbers are encouraged.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -29 -TABLE 7 MINIMUM PLANTING REQUIREMENTS Lot Width Deciduous Trees Evergreen Tree Shrubs 60-100’ 3 3 30 50’-60’
2 1 20 40’-49’ 1 1 15 30’39’ 1 10 < 30’ 1 5 All disturbed areas must be re-vegetated with sod, grass, groundcover, or shrub masses. Homes with plant strips between the houses and the
driveway are required to plant groundcover selected from the Belvedere Landscape Palette. Minimum Plant Sizes at Time of Installation: Tree Size Deciduous 2 ½” caliper (well branched)
Evergreen 6’ height (full) Shrubs 3 gallon container Landscape Specifications: The following specifications are the minimum standards that are acceptable for the installation of plant
material in the residential neighborhoods: 1. The contractor shall be responsible for site inspection prior to landscape construction and installation in order to acquaint himself with
the existing conditions. The Contractor shall be responsible for locating all existing underground utilities prior to beginning construction. Any planting conflict arising from existing
utility locations shall be brought to the attention of the Owner. 2. The Contractor shall be responsible for providing positive drainage at 2% minimum in all planted areas. 3. The Contractor
shall verify plant count from the plan, and shall provide and install all plant materials shown on the approved plan. The plant schedule provided is for the Contractor’s reference only;
quantities shall be verified from the approved plan. 4. The Contractor shall guarantee all plant materials for 1 year from the date of planting. 5. The Owner or his designated agent
shall approve any changes in plant material. 6. All plant material shall be balled and burlapped or container grown and shall be well formed, vigorous, growing specimens with growth
typical of the variety specified and free from injurious insects and diseases. 7. All trees and shrubs shall be installed as indicated on the approved landscape plan. 8. All plants and
beds shall be mulched with a 3 inch layer of mulch
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -30 -c. Guidelines for Tree Preservation Preservation measures shall be administered to trees within wooded areas
to be maintained within the conservation/preservation areas delineated in the General Development Plan, with particular preservation effort directed toward trees with trunk diameters
greater than 18 inches at breast height. All wooded preservation areas adjacent to existing residential development shall be fenced off from construction activity with portable chain
link fencing no closer than the dripline of any tree growing inside the preservation areas. All other wooded areas to remain shall be fenced off from construction activity with 40 inch
high “international orange” plastic web fencing no closer than the dripline of any tree growing within the designated conservation/preservation area. Silt fencing shall be utilized at
stream buffers. During the course of final grading, if it becomes necessary to fill within the canopy limits of existing trees, such fills shall not exceed depths greater than six (6)
inches to ensure continued saturation of the existing root mat. Prior to grading around the trees, all vegetation shall be stripped from the fill areas and fertilizer shall be applied.
Should it become necessary to cut within the canopy limits, all disturbed roots shall be protected from exposure to the air. The crown leaf surface shall be proportionately reduced to
balance the reduced root system. The trees shall be fertilized upon completion of grading activities in the area. Any damaged portions of trees within wooded areas to be maintained shall
be immediately addressed to promote expedient recovery. Further measures for tree protection are outlined in Chapter 3.38 “Tree Preservation & Protection” of the Virginia Erosion and
Sediment Control Handbook. 4. STREET CLASSIFICATIONS The transportation network of Belvedere will be through a system of Traditional neighborhood Design (TND) styled streets that are
based on the following principles.* TND Streets Defined -A Traditional Neighborhood Development (TND) is a human scale, walkable community with moderate to high residential densities
and a mixed-use core. Compared with conventional suburban developments, TND’s have a higher potential to increase modal split by encouraging and accommodating alternate transportation
modes. TND’s also have a higher potential for capturing internal trips, thus reducing vehicle miles traveled. -A dense network of narrow streets with reduced curb radii is fundamental
to TND design. This network serves to both slow and disperse vehicular traffic and provide a pedestrian friendly atmosphere. The overall design should ensure that non-vehicular travel
is afforded every practical accommodation that does not adversely affect safety considerations. The overall function, comfort and safety of a multi-purpose or “shared” street are more
important than its vehicular efficiency alone. TND’s have a higher proportion of interconnected streets, sidewalks and paths. Streets and rights-of ways are shared between vehicles (moving
and parked), bicycles and pedestrians. The dense network of TND streets functions in an interdependent manner,
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -31 -providing continuous routes that enhance non-vehicular travel. Most TND streets are designed to minimize through
traffic by the design of the street and the location of land uses. Streets are designed to only be as wide as needed to accommodate the usual vehicular mix for that street while providing
adequate access for moving vans, garbage trucks, fire engines and school buses. -Intent: That the development encourages walking and biking, enhanced transit service opportunities, and
improved traffic safety by promoting low speed, cautious driving while fully accommodating the needs of pedestrians and bicyclists. The development should reduce the number of external
vehicle trips, and thus vehicle miles traveled through provision of recreational and other resident-oriented destinations within a walkable community. The traffic impacts, both on-site
and off-site, should be minimized. Incorporated into the Code of Development are transportation classification standards for the principle streets, alleys and travel ways within Belvedere
as summarized in the following Table 8. These standards were crafted using the VDOT “Road Design Manual” guidelines issued January 1, 2005. NOTE: All streets and sidewalks shall be designed
and constructed to satisfy the minimum applicable design and construction standards required by the Subdivision Ordinance at the time such designs are approved for construction. Variation
# 32 (approved 2.3.10) Elimination of Road C from Table 8 Road Standards. Variation # 33 (approved 2.3.10) Modification of Table 8 Road Standards to Change the streets in Block 2 (road
A and B) from public streets to private streets.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -32 -Street Name Street Type Public or Private Design Speed (MPH) Traffic Flow Travel Lanes (Tot. #) Bike Lanes
On-Street Parking Median Paved Width, Min Fc-FC Min Planting Strip Min Sidewalk Width Row Width (3) Exhibit 11 Cross Section Belvedere Blvd. Rio Road to Roundabout #1 Parkway Curb NO
gutter pan Public 35 2 way 2 2 (5') striped N -34' 6' N/A* 100’ Exhibit 11 (1) Belvedere Blvd. -Between Roundabout #1 and Road d Boulevard w/Splitter Island at Roundabout #1 Public 25
2 way 2 Y N 8’ min 35' 6' East Side Only 5' East Side Only 76' Exhibit 13A Belvedere Blvd Road d to Road e OPTION 1 Boulevard Public 25 2 way 2 Y N N 34' Varies 6' to 2.5' 5' East Side
Only 44.55' Exhibit 13A Belvedere Blvd Road d to Road e OPTION 2 Boulevard Public 25 2 way 2 Y N N 34' 6' 5 58' Exhibit 13 Belvedere Blvd Road e to Road K Divided Blvd. Public 25 2 way
2 Y Y Inbound Only 8' minimum 22' inbound 18' outbound 6' 5' 76' Exhibit 11 (2) Belvedere Blvd Road K to Village Green Boulevard Public 25 2 way 2 Y Y Y 22' inbound and outbound 6' 5'
76' Exhibit 11 (3) Belvedere Blvd @Village Green Eastside (inbound) Street (One Way) Public 20 1 way 1 N Y w/bumpouts exterior only N 22' 6' 5' 42' Belvedere Blvd @Village Green Westside
(outbound) Street (One Way) Public 20 1 way 1 N N N 16' 6' N/A* 40' I,H (East of Bel. Blvd.), K,P Street Public 20 1 way 1 N Y (Rt Side Only) ** N 22' 6' 5' 46' Exhibit 11 (7) D East
(Betweeen Streets N and J) Street Public 25 2 way 2 N Y N 30' 6' 5' 54' Exhibit 11 (5) D East (Betweeen Streets J and F) Street Public 30 2 way 2 N Y(Outbound only w/bump outs) N 32'
6' 5' 56' Exhibit 11 (6) D East (Betweeen Street F and Round About #2) Street Public 30 2 way 2 N N N 30' 6' 5' 54' Exhibit 11 (5) A Street Private 20 1 way 1 N Y 20' min 22' 6' 5' 48’
Exhibit 11 (7) B,C Street Private 20 2 way 2 N Y N 30' 54' Exhibit 11 (5) E,F,G,H,I, K, L,M,N,O,Q,S Street Public 20 2 way 2 N Y N 28' 6' 5’ 52' Exhibit 11 (4) I,O,Q,S Cul-De-Sac Public
20 1 way 1 N N 30' Radius Min. 22' 6' 5' 128' Roundabout #1 Street Public 20 1 way N N 22' 6' 5' T.B.D. Roundabout #2 Street Public 20 1 way N N 22' 6' 5' T.B.D. a,b,c,d,e,f,g,h,i,j,k,l,m
,n,p,s,t,u,v,w Alley (Residential) Private N/A 2 way 2 N N N/A 14' N/A N/A 20’ Exhibit 11 (8) o,q,r, Alley (Residential) Private N/A 1 way 1 N N N/A 12' N/A N/A 20’ Exhibit 11 (8) *
Pedestrian Access to be provided by means of a paved 8' multi‐purpose trail General Table Notes When the street section includes bike lanes and/or planting strips or sidewalks they will
be provided on both sides of the street unless otherwise indicated Urban street sections will provide curb & gutter unless otherwise indicated ROW extends a minimum of 12' from back
edge of sidewalk TABLE 8 ROAD STANDARDS ** On‐Street Parking will be permitted only along portions of these streets that are adjacent to parks and/or open space
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -33 -Parking Areas Off street parking and loading within the Belvedere Development will be provided in accordance
with Section 4.12 of the Albemarle County Zoning Ordinance. Further, all parking/loading requirements will be met within the land mass encompassing Belvedere. Parking for the development
will be in either surface spaces or structured. In addition, the layout of the site allows for appropriate passenger collection points as well as vehicular circulation patterns which
could accommodate future mass transit access to Belvedere. 5. PRESERVATION OF HISTORIC STRUCTURES, SITES, AND ARCHAEOLOGICAL SITES The Belvedere project encompasses an area of the county
with a long history of human habitation. There is evidence of habitation by early Native Americans along the extensive floodplain. A section of the property lying on either side of Free
State Road encompasses lands traditionally occupied by the Free State Community one of the Commonwealth’s earliest recorded free African-American communities. The roots of the Free State
Community extend back to the latter half of the 18th Century and the community’s residents included members of the Hemmings family. The Applicant commissioned a Cultural Resources Reconnaissance
Survey which was prepared by the William & Mary Center for Archaeological Research. This report dated November 20, 2003 has been submitted to the county. On the basis of this study the
Applicant has commissioned two additional studies of the Belvedere property. The first is an architectural Reconnaissance Survey of Existing Resources, prepared by Arcadia Preservation
, LLC of Keswick dated December 7, 2004. Documenting all previously identified historic structures within the property boundaries. Each site was photographed, mapped, had a VDHR DSS
entry created, and when feasible site sketches and floor plans were created. This study found none of the structures to be capable of preservation either individually or as a district
district due to their “deteriorated condition and loss of integrity.” A copy of this report including archival photos, brief architectural descriptions, and sketch site and floor plans
(When accessible) was filed with the county and the Virginia Department of Historical Resources in December 2004. The second is a Phase I archaeological study by Rivanna Archaeological
Associates. The Phase I study was completed on February 22, 2005 and identified 2 sites which merit additional archaeological investigation to “further evaluate the extent, nature, and
integrity of Early National (1789-1830) and Antebellum (1830-1860) Period deposits.” The study also identified a “likely location of an historical cemetery.” The Applicant is currently
reviewing proposals for Phase II archaeological investigations of the two sites identified in the study (VDHR 44AB518 and VDHR 44AB374) as well as a field study to conclusively verify
the existence of a historical cemetery and delineate the boundaries of said cemetery should its existence be verified by the archaeological investigation.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -34 -The contractor hired to perform any Phase II or Phase III work shall, at a minimum, provide a Principal Investigator
who meets or exceeds the professional standards set by the Secretary of the Interior. Should Phase II investigation indicate that either of these sites may be eligible for listing in
the National Register of Historic Places, the Applicant shall initiate a Phase III investigation of the affected site(s). The decision as to whether a Phase III investigation is merited
shall be made on the basis of the Final Report in consultation with the County of Albemarle Director of Planning. All Phase I, Phase II, and Phase III studies shall meet the Virginia
Department of Historic Resources’ Guidelines for Preparing Archaeological Resource Management Reports and the Secretary of the Interior’s Standard and Guidelines for Archaeological Documentation,
as applicable, and shall be conducted under the supervision of a qualified archaeologist who meets the qualifications set forth in the Secretary of the Interior’s Professional Qualification
Standards. All approved treatment plans shall be incorporated into the plan of development for the site and shall be adhered to during the clearing, grading, and construction activities
thereon. The Applicant commits to initiate the Phase II investigation by October 1, 2005 and to initiate a Phase III investigation, if warranted, within 60 days of receipt of the Final
Report from the Phase II investigation. Curation of Historical Artifacts: Should Phases I or II or III studies yield objects or artifacts of archaeological significance, these objects
shall be conveyed to the Virginia Department of Historic Resources for long term preservation. Should Phase III fieldwork yield subsurface architectural features and artifacts related
to 18th-or early 19th-century domestic occupations at Free State, and should these sites be deemed archaeologically significant by archaeologists with
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -35 -the Digital Archaeological Archive of Comparative Slavery (DAACS) , based at the Thomas Jefferson Foundation,
these artifacts will be submitted to the archaeologists at the Thomas Jefferson Foundation for analysis and entry into DAACS prior to being conveyed to the Department of Historic Resources.
The Belvedere Station Land Trust will be solely responsible for conveying all artifacts analyzed by DAACS to the VDHR. Roadside Markers The Owner shall fund $5,000 toward the construction
and installation of two roadside historical marker (as provided in Proffer 6.3) providing information on: • the Free State Community and prehistoric communities that once inhabited the
site. • Prominent historical figures who resided in the community such as Critta Hemmings and Amy Farrow. • Prehistoric Native American Community The sign language and location shall
be approved by the Director of Planning and be completed by Albemarle County no later than than 12 months following the approval of the site plan of the phase in which the markers will
be located. 6. Lot Layout Standards: In keeping with the tenets of New Urbanism, the lot layout standards for Belvedere are intended to create a streetscape that creates a sense of community
and allows the street to function as a public space that draws a neighborhood together, fostering a sense of inclusiveness and community. Table 9: Block 2-10 Residential Lot Regulations
Variation # 21 (approved 3.24.08 & revised 7.25.08) “build-to” range Variation # 22 (approved 3.24.08 & revised 7.25.08) alley fed rear setback Carriage Houses & Accessory Structures
Townhouse SF 30'40' SF 41'‐50' SF 51'‐60' SF >60' All Lots Front Build‐to from Street 2 8' ‐16' 8' ‐16' 8' ‐16' 8' ‐16' 16' (same as Primary Structure) Side Setback 3,4 0' 3' 3' 3' 5'
(same as Primary Structure) Rear 1 10' 10' 10' 10' 10' 4' Rear 4' 4' 4' 4' 10' 4' 5. Carriage houses must be located to the rear of the primary residence. 6. Other accessory structures
structures may not be placed in front of the primary structure. Primary Structures 1, 4 1. Porches (1&2 story), stairs, balconies, bay windows, planters, chimneys,
terraces, eaves, and entrance stoops may encroach into the area between the minimum build‐tp range and the front r.o.w. line up to 4' from the front r.o.w. line. They may encroach into
the area between the rear setback up to 4' from the property lin or, in the case of an alley easement, within 4' from the easement boundary. 2. No encroachments are allowed within the
minimum side yard. 3. Where a side setback of less than 4'11" is used, a 6' maintenance easement shall be recorded on all properties adjacent to the side setback of less than 4'11".
4. Where an alley adjoins a side yard, the minimum setback is 3'. Min Depth 1 Max Depth Min Width 4' 10' 8' 5' 10' 8' 3' 5' 4' Covered Porches Townhomes Covered Porches Single Family
Homes Open Porches Single Family & Townhome Restrictions Governing Structures Extending Beyond the Front Build‐to Line 1. The dimensions of a porch shall be measured from the edge of
the house to edge of the floor area and shall not include any steps.
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -36 -Table 10: Commercial, Multifamily or Civic Use Lot Regulations Variation # 23 (approved 3.24.08 & revised
7.25.08) front and rear setbacks in Block 1, 2, 4 Multi‐Family, Commercial, or Civic Buildings Block 1 Block 2 Block 4 Front Build‐to from Street 1 5' 5' 5' Side Setback 5' 5' 5' Rear
10' 10' 10' 1. For structures with frontage on more than 1 right of way, the build‐to lines shall apply only to the primary elevation For Blocks 3 and 5-10 All Commercial and Civic Buildings
shall be subject to the applicable residential setbacks and build‐to lines Maximum Building Heights 1 Max Blocks 1&2 50' Blocks 3-10 38' 1. To be measured in accordance with applicable
regulations of the Albemarle County Zoning Code Minimum and Maximum Lot Size: Residential: Blocks 2-10 The minimum residential lot size shall be 825 Ft2 with a minimum frontage of 15’
and a minimum side lot line of 55’ The maximum lot size for a residential lot in Belvedere shall shall be 35,000 Ft2 with a maximum frontage of 200’ and a maximum side lot line of 175’.
Commercial The minimum commercial lot size in blocks 1 through 10 shall be 450 Ft2 with a minimum frontage of 15’ and a minimum side lot line of 30’ The maximum lot size for a commercial
lot in Blocks 1 shall be 300,000Ft2 with a maximum frontage of 1,000’ and a maximum side lot line of 1,000’. The maximum lot size for a commercial lot in Blocks 2 and 4 shall be 18,000
Ft2 with a maximum frontage of 120’ and a maximum side lot line of 150’. Appendix A– Carriage House Units General Standards: All Carriage House Units must be constructed in the same
architectural style as the primary residence and must employ the same exterior color selections as the primary residence. Setback regulations for Carriage House Units shall be the same
as those for garages Carriage House Units are separate, detached independent living units which are included with a single family detached unit and clearly subordinate to the primary
residence. These units are typically located above a garage and are restricted to a maximum finished area of 800 ft2. While these units may have a distinct street address and may be
provided with separate utility meters if utilized as a rental unit, they may not be subdivided from
BELVEDERE CODE OF DEVELOPMENT • BELVEDERE 10/10/05 (As Revised 2/3/10) -37 -the primary residence. Carriage house units must be located to the rear of the primary residence and must
meet all architectural standards applicable to the primary residence. Setbacks shall be the same as those applicable to a traditional detached garage. Carriage house units play an important
role in providing for affordable housing. As an inexpensive rental unit, they help provide affordable rental housing that is integrated into the larger community. An additional benefit
is that the units are “Cash flow positive” helping to make the primary residence more affordable by providing the owner with additional cash flow to pay the mortgage. These units have
been widely utilized in other TND neighborhoods with tremendous success. Some examples of typical carriage house units